Skip to content

Anet A6 Review – Experiences and Improvements

The days of expensive “ready-made 3D printers” are numbered! Well, not quite. Nevertheless, there is now an affordable alternative for acquiring a functional 3D printer for under €200. This involves so-called “3D printer kits”, i.e. a 3D printer for you to assemble yourself. We have assembled and extensively tested one of the most well-known printer kits – the Anet A6 – for you. Whether the kit is also suitable for beginners and whether the printer actually produces clean prints after assembly – you can find out more in this test report!

Anet A6 3D printer test

Test results

7,6 out of 10 pointsOur score (out of 10)

Pros

  • Good print quality
  • Large pressure area
  • High customisation potential
  • Price

Cons

  • Quality control
  • Faulty assembly instructions
Contents

First impressions of the Anet A6

Anet is one of the most well-known 3D printer manufacturers from China. In addition to the less well-known "Anet A6", the manufacturer also offers the much more popular model "Anet A8", as well as other pre-assembled printers, which fall into significantly higher price categories. This review focuses on the Anet A6. First, however, we will take a closer look at the main differences between the two affordable Anet models.

Anet A6 vs. Anet A8

Both models are 3D printer kits that differ mainly in detail. The most relevant difference between the Anet A6 and the Anet A8 is the larger display of the A6 and the single-knob control. The display of the Anet A6 shows up to 12,864 pixels, whereas the A8's display only reaches 2,004 pixels. The Anet A8 is operated via 5 control buttons. The Anet A6, on the other hand, features a single-knob interface with rotary control. The mainboard used is now identical for both models.

Another difference is the guidance of the X-axis. The A8 has vertical guidance, so both shafts run parallel to each other, whereas the Anet A6 shaft guidance is horizontal, i.e. side by side. All holders on the A6 are made of acrylic. Holders on the A8 model were partially created using 3D printing. There is another difference in the scope of delivery. The A6 comes with a 500g roll of white PLA filament. The Anet A8 omits this!

What’s included

The Anet A6 kit is delivered with all necessary components. In addition to the housing parts, the required screws, belts, shafts, guide rods, etc. are also included. The tool required for assembly is also included so that even those without the appropriate tools can easily assemble the printer kit. The manufacturer even includes a 500g spool of white PLA filament with every Anet A6 kit. After assembly, nothing stands in the way of a first print test.

Design and build quality

The Anet A6 was developed based on the Prusa design by Josef Prusa and is largely attributable to the RepRap scene (“Rapid Prototyping and Rapid Manufacturing”). Thanks to the open-source design, it would be possible to reproduce the Anet A6 even without the ready-made printer kit.

The build quality of the printer is good for the price. For the kit tested, no parts needed to be post-processed, and the parts fitted together precisely and could be screwed together. The steel shafts included were straight and could be installed without problems. Nevertheless, these DIY printer kits from China should always be approached with caution. Although the components of our test kit were perfect, it is not uncommon to encounter inaccurate shafts, a warped heat bed or other poorly manufactured parts!

Hardware

The print space of the Anet A6 measures 220 x 220 x 250 mm. The extruder is of the “Direct Drive” type, where the extruder is located directly above the hotend, leading to an increased weight on the X-axis. The nozzle has a diameter of 0.4 mm. The printable layer height is between 0.1 and 0.2 mm. It supports 1.75 mm filament made of different materials (listed are ABS / PLA / HIPS). Anet specifies the accuracy of the X and Y axes as 0.012 mm. That of the Z-axis is 0.004 mm. The motors used are unspecified NEMA17 stepper motors. The mainboard is of the Anet V2.0 type.

Assembling the Anet A6

Oh dear, where is the instruction manual? A printed assembly manual is not included with the Anet A6 kit. Instead, Anet includes a USB card reader in the form of a stick with a suitable 16GB micro SD memory card. In addition to the illustrated assembly instructions, the memory card also contains the slicing software “Cura”, the appropriate printer drivers and test files tailored for the A6, which can be printed directly after assembly.

Although the included assembly instructions are largely illustrated, it is advisable for beginners, in particular, to follow the video instructions on YouTube. The step regarding the Z-end stop was even omitted entirely in the illustrated instructions, which would surely have led to a lot of frustration at the end of the assembly. But you should not rely 1:1 on the manufacturer's video instructions either. The heat bed carrier is mounted the wrong way round in both instructions, meaning the belt does not run parallel.

You can watch the assembly of our test unit in this video.

Play video on YouTube
When you play the video, it loads from YouTube; data is transferred to Google in the process.

Calibration of the Anet A6

Before you can even start printing, the printer still needs to be calibrated. The Z and X axes must run parallel, the heatbed on the Y-axis must be level, and the distance between the nozzle and the heated bed must also be adjusted. The height of the heated bed can be corrected using four threaded rods with wing nuts. The maximum distance to the nozzle should not exceed 0.1 mm. To achieve this distance, take a sheet of paper and place it on the heated bed. If you move the nozzle over it, you should feel slight pressure on the sheet. All belts of the printer should be adequately tensioned, otherwise inaccurate print results will occur.

Another step is the insertion of the filament. To gain initial experience, you can safely use the included filament. The filament is inserted directly into the extruder. To do this, press down the metal spring lever and push the filament through the small opening. Then, with a bit of feel, guide the filament past the drive wheel through another opening directly into the nozzle. You can see whether the filament has been inserted correctly if liquid filament comes out of the nozzle. Of course, you should preheat the nozzle to approximately 200°C beforehand! The filament can be removed by pushing a few centimetres through the preheated nozzle, pressing down the lever and pulling the filament upwards with momentum.

To illustrate this better, here is another video on calibrating the Anet A6

Play video on YouTube
When you play the video, it loads from YouTube; data is transferred to Google in the process.

 

First print tests

If the steps mentioned above have been carried out correctly, nothing stands in the way of a first print. For beginners, it is recommended to start by printing the print files provided on the SD card. To print, insert the SD memory card into the corresponding slot on the mainboard. Then switch on the Anet A6 and select the SD memory card as the print medium. Alternatively, it is also possible to print via a connected computer. A connection between the computer and the printer is established via the USB interface of the mainboard. The required drivers are also on the SD memory card.

Once a print job is started, the heated bed and nozzle will heat up to the temperatures specified in the GCODE file. The current temperature can be read and monitored via the display. The heated bed temperature typically lies between 50°C and 60°C. The nozzle temperature depends on the respective filament. Most filament manufacturers provide the suitable printing temperatures. The recommended printing temperatures are also specified on the included Anet filament. However, experimentation is key here too! In our first print attempts, the heated bed was set to 50°C and the nozzle to 200°C by default. We achieved better print results with the Anet filament at 60°C and 210°C. A recommended first print test is the "XYZ Calibration Cube". This small cube prints quickly, and the accuracy of the print can be measured with callipers.

Our first printing experiences with the Anet A6 are more than positive. If all steps for commissioning are observed, even the first print attempt can succeed and deliver an accurate result. Compared to far more expensive pre-assembled printers, the Anet A6’s print result is in no way inferior to theirs.

Download a GCODE tuned for the Anet A6 for the XYZ Calibration Cube here: https://www.dropbox.com/s/u5dtx1a989sivrw/AA_xyzCalibration_cube.gcode

CAD and slicer

Custom 3D models are created using so-called "CAD programs". One of the most beginner-friendly is "TinkerCAD", a "browser-based 3D design and modelling tool". Here you can start modelling immediately without having to download any software and export your finished 3D model as an STL file. Advanced users should take a look at "SketchUp". This free 3D program is more complex but also offers significantly more modelling options.

Once you have created a 3D model and saved it in STL format, you need a so-called “slicer” program to create printable GCODE from it. The best-known free 3D slicer is “Cura”. After downloading and installing Cura, you have to create a new 3D printer profile with the appropriate Anet A6 parameters. Beginners can also use the ready-made profile from “maciekish”. The 3D model in STL format is now imported into Cura. You can then adjust numerous print parameters. In addition to speeds, you can also specify layer height, infill and other parameters as GCODE. Additionally, you get a preview of how the print will proceed, how long it will take, and how much filament will be used. The GCODE can be exported to the SD memory card, or you can print directly from Cura, as long as Cura is connected to the Anet A6 via the USB interface.

Cura3D
Cura3D

Anet A6 improvements

A DIY 3D printer is often an extensive tinkering project, where one is happy to swap out components to achieve even better print results. On the one hand, there are printable improvements that are relatively simple to implement, but there are also extensive modifications that significantly alter the original Anet A6. An overview of possible modifications can be found below. We have already thoroughly tested many of the improvements listed here ourselves.

Printable improvements

Fan-Duct (fan): This improvement ensures uniform cooling of the filament and is among the most important printable upgrades.

Fan Duct by Paclanc*

Y-belt tensioner: To ensure the Y-axis belt remains properly taut, it is recommended to print this belt tensioner.

Y-Belt Tensioner by Photograaf16*

X-Belt Tensioner: The X-axis belt should not sit loosely either. This belt tensioner provides a good solution.

X-Belt Tensioner by vernierroger*

Table nut cover (heat bed screws): This improvement makes the heat bed even easier to calibrate.

Tablet Nut Cover by AndrewUsov*

Filament Guide: To prevent the filament from tangling, this practical Filament Guide feeds it evenly into the extruder.

Tablet filament guide by CanalVap*

Interchangeable improvements

Igus plain bearings (RJ4JP-01-08): One of our first non-printed upgrades was replacing the original ball bearings with Igus plain bearings RJ4JP-01-08. These all-plastic plain bearings are made from a special iglidur® plastic that is particularly wear-resistant and self-lubricating. The advantage of the Igus plain bearings over the LM8UU linear bearings used as standard is reduced noise and maintenance-free operation. To retrofit the Igus RJ4JP-01-08, you need a total of 8 such plain bearings, available from just €2 each.

Igus RJ4JP-01-08 plain bearing*

Igus precision aluminium shaft (AWMP-08): The steel shafts included in the Anet A6 printer kit are not of particularly high quality. Those looking for an affordable alternative should take a look at the Igus precision aluminium shafts. These anodised solid aluminium shafts are available directly from Igus starting at €8.65 per metre. Of course, you can also have the shafts cut to the right size. In our test, the shafts of the X-axis were replaced with two AWMP-08 and four Igus RJ4JP-01-08 shafts. While the carriage glides somewhat more heavily on the X-axis overall, the reduced noise level is clearly noticeable. The print result also feels more accurate.

Igus AWMP-08 shafts*

GT2 timing belts and pulleys: Replacing the original timing belts and pulleys is a worthwhile upgrade. Unfortunately, Anet uses a very stiff timing belt that loosens comparatively quickly as tension increases. Switching to 20-tooth pulleys is also interesting. Pulleys with more teeth allow for higher print speeds. Conversely, pulleys with fewer teeth enable more precise printing results. If you replace the pulleys and timing belt, ensure that the steps-per-unit settings remain correctly calibrated.

  • 16 teeth: 100 steps/mm
  • 20 teeth: 80 steps/mm
  • 25 teeth: 64 steps/mm

GT2 toothed belt with pulleys*

E3D-V6 Bowden: It is also interesting to convert the direct extruder to the E3D-V6 Bowden extruder. The advantage of a Bowden conversion is the lower weight on the X-axis, which can achieve more accurate prints at higher print speeds. At the same time, however, the distance between the extruder and nozzle increases, which makes it very difficult to print soft filaments with a Bowden set-up. For those who like to switch, an E3D-V6 Bowden extruder replica, available from 7€, is recommended. Of course, the X-axis carriage must also be converted accordingly for Bowden. A very good design with the nice name "Frankenstein" is available on Thingiverse.

E3D-V6 Bowden extruder*

Inductive / capacitive proximity sensor: Constantly realigning the heatbed can quickly become frustrating in the long run. A capacitive or inductive proximity sensor that replaces the Z-end stop provides a remedy. The proximity sensor is attached directly to the extruder carriage. Manual correction of the distance height between the nozzle and heatbed is no longer necessary. However, for such a "autolevel" mod to succeed, a different firmware must be flashed to the mainboard of the Anet A6. The most well-known alternative firmware for the Anet A6 and Anet A8 printer series is the so-called "SkyNet 3D" firmware. There are also some things to consider with the sensors themselves. A capacitive sensor is best chosen if printing on a glass surface, as an inductive sensor does not detect glass. An inductive sensor, on the other hand, usually works more precisely but mainly detects metallic objects. You should also pay attention to the voltage with which the proximity switch is operated. Most sensors are operated with 6 to 36 volts. Some sensors can also be operated with only 5 volts, but measurement errors are common. For the sensor to be correctly recognised by the Anet mainboard, it is recommended to insert a optocoupler in between so that no residual voltage remains during switching.

LJC18A3-H-Z/BX (capacitive)*

LJ18A3-8-Z/BX (Inductive)*

Glass plate as build surface: If the filament doesn't adhere properly, or if you don't want to constantly change the Blu-Tape, switching to glass as a build surface is recommended. Most specialist retailers can cut a suitable glass plate (215 x 215 mm) to size for you. Alternatively, you can buy a pre-cut borosilicate glass plate. The advantages of glass are its very good adhesion, ease of cleaning and the very smooth print result. If the print doesn't adhere directly to the glass, you can use some hairspray to create a better base structure. If the filament still doesn't adhere, applying a thin layer of UHU-Stic to the glass surface will help. This guarantees that even the most difficult-to-adhere filaments will stick!

Borosilicate glass plate*

techreviewer TEST VERDICT OKAY 7,6/ 10 2018 Anet A6
Award graphic (SVG)

Our verdict

Just set it up and start printing is not possible with the Anet A6. With this 3D printer, you have to get your hands dirty, as you only receive the parts required to assemble a printable 3D printer. Ease of entry is mediocre. The assembly instructions are partly incorrect, and you should initially read extensively about the "Anet A6" topic. Even after finally assembling the 3D printer after hours, it still needs to be calibrated and adjusted to achieve clean print results.

However, if you enjoy tinkering and have a passion for DIY, the Anet A6 is one of the most affordable ways to assemble a functional 3D printer. If you were to buy all the individual parts separately, you would probably end up paying more than if you bought the Anet A6 Print-Kit outright. The Anet A6 and A8 printer kits are currently produced at cost. However, Anet forgoes support, and unfortunately, quality control suffers as a result. Although you might get lucky and have all parts fit perfectly, it is quite possible to end up with a kit featuring, for example, bent shafts, faulty threads, or a warped heatbed.

In summary, however, it can be said that the Anet A6 printer kit is worthwhile. The modification potential is limitless and the print quality is also convincing. If you want to get into 3D printing on a budget, you should definitely consider the Anet A6 printer kit!

Specifications

General
Model
Anet A6
Type
FDM printers
Enclosure material
Acrylic
Motherboard
Anet V2.0
Print speed
40 - 120 mm/s
XY accuracy
0.012 mm
Z-axis accuracy
0.004 mm
Size
48.00 x 40.00 x 40.00 cm
Weight
9 kg
Nozzle
Type
Single
Diameter
0.4 mm
Temperature
up to 260°C
Layer height
0.1 - 0.4 mm
Print bed
Build plate size
220 x 220 x 250 mm
Heated bed
Yes
Extruder
Type
Direct
Material
1.75 mm ABS, HIPS, PLA, etc.
Reviewed by

Timo Altmeyer

Timo is the founder of techreviewer.de and a true technology expert. From smartphones to e-bikes, and from home cinema to smart homes, he always has his finger on the pulse of the latest trends.

To author profile →

Comments (10)

  1. In your videos, you have a glass plate on the print bed. Which one is it and where can you get it? Thanks.

    Replies
  2. Hi, I cut the glass plate together myself from picture frame glass. The cost was about €3. Of course, you can also buy plates cut to size, but they are considerably more expensive. You can also get a glass cutter from just a few euros.

    Replies
  3. Hello, have you already tried SkyNet with the Anet A6? I ordered the sensor yesterday, but I don’t know exactly what to do with it. Can I connect it directly or do I need an optocoupler, as you wrote?

    Replies
  4. Hi, I'll flash SkyNet in the coming days. I was waiting because the LJC18A3-H-Z/BX shipped from DE was out of stock on Amazon (but it is available again now!). I have the sensor here now. Which one did you order? The LJC18A3-H-Z/BX NPN NO could potentially be operated at 5V without an optocoupler. I have no idea how inaccurate the measurement results would be then, but I'll try it out.

    Replies
  5. Peter Markwart

    Spot on! Many thanks for this detailed Anet A6 test. I have just ordered the printer from Gearbest and I am really excited. How long do you think shipping will take?

    Replies
  6. Hello,

    First of all, thank you very much for the detailed test, which helped me a lot with my first steps with the Anet A6. Based on my experience with the printer, I would like to post something here, perhaps it will help someone else.

    Replaceable improvements:

    1. In my opinion, a different holder for the heat bed should be at the very top of the list. The supplied “H” is far too soft and weak. It warps constantly, a) while heating up and b) under the tension of the springs and screws used to level the bed. I replaced the holder with this one and am very happy with the result: ruthex Heatbedholder / Heizbetthalter – Anet A8 A6 E10. It costs around 30 euros from a large online retailer. Not cheap, but worth it, partly because it also comes with plates that can be screwed between the holder and the Y-belt mount to improve belt alignment.

    2. Replacing the bed levelling springs with silicone spacers. Advantage: Springs under permanent pressure lose their tension and become soft, requiring frequent bed re-leveling. Silicone significantly improves stability. Suitable spacers are available, for example, here: https://shop.bohrers.de/silikonpuffer-4stk.html

    3. Silcawool insulation between the heated bed and the heated bed holder. This reduces heat loss and allows for faster heating of the heated bed. A suitable mat in the size of the heated bed is available, for example, here: https://shop.bohrers.de/heizbettisolierung-silcawool-220-220-13mm-285.html
    Together with 15mm silicone buffers and the new heated bed holder, it provides excellent printing results for me.

    4. Alternative to the borosilicate glass plate: I got myself the glass plate from Anycubic (ANYCUBIC Ultrabase 3D). This is simply glued onto the aluminium heated bed. It also has bevelled edges, so you can reach the screws of the heated bed even with the plate mounted.
    With this glass plate, you don't need any additional adhesion enhancers (hairspray, UHU glue stick or similar). I print PLA at a bed temperature of 50-60 degrees. The PLA adheres like concrete to the glass plate (provided everything is correctly adjusted). Once the heated bed has cooled to around 30 degrees after printing, the printed object detaches from the glass surface on its own and can simply be removed. Since no additional adhesion enhancers are needed, the glass plate remains clean and only needs to be cleaned occasionally with alcohol/glass cleaner.

    Printable improvements:

    1. A6 Flexible Filament Guide: https://www.thingiverse.com/thing:2242903
    This is actually intended to make processing/inserting flexible filament easier, but it also greatly simplifies changing standard filament. The method described in this article, pushing the filament through the hot nozzle and then pulling it out of the extruder with a jerk, resulted in a clogged extruder (or throat-to-nozzle connection) in 7 out of 10 attempts for me. Having to disassemble the extruder every time you change filament is annoying. With this printable add-on, filament changes now work smoothly. I cut the filament above the extruder entry and let the extruder (naturally with a hot nozzle) extrude filament until nothing comes out at the bottom (approx. 40–50 mm). Then I insert the new filament from the top so that it is straight and gripped by the extruder, and let it extrude again. The extruder straightens the new filament slightly while pushing it downwards, pushing the old filament out of the nozzle. You naturally have to keep extruding until the new filament comes out at the bottom. This type of filament change obviously uses more filament (approx. 5 cm of old and a few cm of new) than pulling the filament out from the top. But for me, it's worth it, as I don't have to constantly disassemble the extruder.

    A few more notes on the article:

    1. There is no Anet Board V2.0. The version number shown on the display refers to the firmware. The board is still version 1, possibly with an additional revision number. The board that came with my A6 in November was still marked “V1.0”; the one I additionally ordered for testing and tinkering is printed with “V1.5”.

    2. GT2 timing belts and pulleys: Installing only pulleys with 20 teeth per inch achieves nothing, as the supplied belt has 16 teeth per inch. The belts must also be replaced. Furthermore, it should be URGENTLY noted that the steps-per-mm settings in the printer's configuration must be adjusted. If printing continues with the settings for the old 16-tooth belts, the printed parts will be too large. The settings for the X and Y axes must be changed to 80 steps/mm so that the prints (in terms of size) fit again.

    3. Y-belt tensioner: Belt tensioners like the one linked above should not be used without a so-called “frame brace,” such as this one: https://www.thingiverse.com/thing:1896013
    This kind of reinforcement prevents the front mounting plate that holds the belt tensioner from bending in the middle (due to the pressure from the screw) or even breaking if you accidentally overtighten the screw.

    Oh, and one more tip from personal experience: if the prints do not turn out as expected because individual layers are repeatedly shifted, check, in addition to all other possible sources of error (belt tension, loose screws, axes shifting on which the print head and heated bed run, etc.), whether the hotend is wobbling. The print head does come pre-assembled with the kit, but that does not mean it is assembled correctly. There is a nut at the hotend that is supposed to sit as a lock nut under the plate through which the hotend is guided to the extruder (print head carriage). In my case, the nut was located directly at the heating block, i.e. at the wrong end of the hotend. As a result, it wobbled like a tail during fast movements of the print head, which ultimately led to the shifting of individual layers during printing. After I tightened the nut correctly under the print carriage, the printer now prints really well.

    Replies
  7. Hi Stephan, many thanks for the very detailed article and useful tips. I have added the info about the steps for the pulley and timing belt change above. I’ll certainly have more time for the A6 again in winter. Then the article will be completely revised :).

    Replies
  8. Hello,
    I am currently assembling my Anet A6 and would like to install the improvements you mentioned right from the start.
    Did you only replace the X-axis shafts with the precision aluminium shafts, or did you also replace those of the other axes?
    Thanks and best regards

    Replies
  9. oswald brotschinsky

    Thanks, that was extremely helpful.

    Replies
  10. Hello,
    I have a problem where the X-axis mount extends into the top of the ceiling, i.e. into the screws at the very top or, if these are removed, into the acrylic.
    So I cannot reach 240mm at all (250 is not even available in the firmware, verifiable in manual position adjustment mode)
    Is there a solution for this?

    It is never 500g anyway. Maybe 50?

    How did you route the cables from the extruder to the mainboard? Mine are getting pinched between the left rods and the extruder.

    Replies

Write a comment

By submitting, your name, email, and comment will be stored. Find out more in our Privacy Policy. We review comments with multiple links before approving them.

The techreviewer newsletter

The week’s top reviews, news, and deals – delivered straight to your inbox.